<%NUMBERING1%>.<%NUMBERING2%>.<%NUMBERING3%> PRTG Manual: SNMP Library Sensor

APC UPS.oidlib

Can be used to monitor uninterruptible power supplies (UPS) from APC American Power Conversion Corp.

APCSensorstationlib.oidlib

Can be used to monitor alarm status, communication status, humidity, and temperature as shown by an APC sensor station.

Basic Linux Library (UCD-SNMP-MIB).oidlib

Can be used to monitor basic system parameters on Linux systems, such as memory, disk and swap, CPU, and more.

cisco-interfaces.oidlib

Can be used to monitor Cisco-specific parameters, for example, the number of present network interfaces on a system, several states of an interface (admin, oper, speed, type, errors, discards, etc.), and more.

cisco-queue.oidlib

Can be used to monitor queues on a Cisco interface, for example, queue depth and its maximum, discarded messages from the queue, the number of the queue within the queue set, and more.

Dell Storage Management.oidlib

Can be used to monitor Dell storage devices. Possible parameters include disk arrays, battery and power supply, fan and temperature, virtual disk, and more.

Dell Systems Management Instrumentation.oidlib

Can be used to monitor the hardware of Dell systems. Possible parameters include ACPower and battery, alerts, base board, BIOS, Baseboard Management Controller (BMC), chassis, COO, cooling, event log, firmware, integrated development environment (IDE), keyboard, memory, port, network, processor, Small Computer System Interface (SCSI), system, temperature, USB, universally unique identifier (UUID), and more.

HP LaserJet Status.oidlib

Can be used to monitor toner, paper, and jam status of an HP LaserJet printer.

Linux SNMP (AX BGP DisMan EtherLike Host).oidlib

Can be used to monitor different aspects of Linux systems.

This file might detect a very large number of interfaces. It might take a few seconds until the selection table is shown.

Linux SNMP (Framework Proxy Noti v2).oidlib

Can be used to monitor different aspects of Linux systems.

This file might detect a very large number of interfaces. It might take a few seconds until the selection table is shown.

Linux SNMP (IP Net SNMP Noti OSPF RMON SMUX).oidlib

Can be used to monitor different aspects of Linux systems.

This file might detect a very large number of interfaces. It might take a few seconds until the selection table is shown.

Linux SNMP (Source TCP UCD UDP).oidlib

Can be used to monitor different aspects of Linux systems.

This file might detect a very large number of interfaces. It might take a few seconds until the selection table is shown

Paessler Common OID Library.oidlib

Can be used to monitor many common hardware devices. It is used for several sensors and is encrypted.

SNMP Informant std.oidlib

Can be used to monitor logical disks, processor, memory, and network interface on Windows systems.

Library

Shows the path to the .oidlib file selected before. This setting is shown for your information only and cannot be changed here.

Library OIDs

Select the parameters of the device that you want to monitor. A list specific to your setup is shown. It contains all counters found in the chosen library that match your device.

Select one or more items by adding a check mark in front of the respective line. You can also select all items or cancel the selection by using the check box in the table header. Use the search box to narrow down to your desired items.

Depending on the kind of the selected entries, PRTG creates the following sensors:

• SNMP Custom Advanced sensor: One sensor for every 10 single values
• SNMP Custom String sensor: One sensor for each selected entry that returns a string value
• SNMP Custom Table sensor: One sensor for each selected table row with up to 10 channels representing values in the columns of the same row

Sensor Name

Enter a meaningful name to identify the sensor. By default, PRTG shows this name in the device tree, as well as in alarms, logs, notifications, reports, maps, libraries, and tickets.

Parent Tags

Shows tags that this sensor inherits from its parent device, group, and probe. This setting is shown for your information only and cannot be changed here.

Tags

Enter one or more tags, separated by spaces or commas. You can use tags to group sensors and use tag–filtered views later on. Tags are not case sensitive. We recommend that you use the default value.

There are default tags that are automatically predefined in a sensor's settings when you add a sensor. See section Default Tags below.

You can add additional tags to the sensor if you like. Other tags are automatically inherited from objects further up in the device tree. These are visible above as Parent Tags.

It is not possible to enter tags with a leading plus (+) or minus (-) sign, nor tags with parentheses (()) or angle brackets (<>).

Priority

Select a priority for the sensor. This setting determines where the sensor is placed in sensor lists. A sensor with a top priority is at the top of a list. Choose from one star (low priority) to five stars (top priority).

The available sensor settings depend on the sensor that the SNMP Library sensor created. For details about settings, see the sections of these sensors:

• SNMP Custom Advanced sensor
• SNMP Custom String sensor
• SNMP Custom Table sensor

Primary Channel

Select a channel from the list to define it as the primary channel. In the device tree, the last value of the primary channel is always displayed below the sensor's name. The available options depend on what channels are available for this sensor.

You can set a different primary channel later by clicking the pin symbol of a channel on the sensor's Overview tab.

Graph Type

Define how different channels are shown for this sensor:

• Show channels independently (default): Show a graph for each channel.
• Stack channels on top of each other: Stack channels on top of each other to create a multi-channel graph. This generates a graph that visualizes the different components of your total traffic.
  This option cannot be used in combination with manual Vertical Axis Scaling (available in the channel settings).

Stack Unit

This field is only visible if you enable Stack channels on top of each other as Graph Type. Select a unit from the list. All channels with this unit are stacked on top of each other. By default, you cannot exclude single channels from stacking if they use the selected unit. However, there is an advanced procedure to do so.

Click to interrupt the inheritance. See section Inheritance of Settings for more information.

Scanning Interval

Select a scanning interval (seconds, minutes, or hours). The scanning interval determines the amount of time that the sensor waits between two scans. You can change the available intervals in the system administration on PRTG on premises installations.

If a Sensor Query Fails

Define the number of scanning intervals that the sensor has time to reach and check a device again in case a sensor query fails. Depending on the option that you select, the sensor can try to reach and check a device again several times before the sensor shows a Down status. This can avoid false alarms if the monitored device only has temporary issues. For previous scanning intervals with failed requests, the sensor shows a Warning status. Choose from:

• Set sensor to down immediately: Set the sensor to a Down status immediately after the first failed request.
• Set sensor to warning for 1 interval, then set to down (recommended): Set the sensor to a Warning status after the first failed request. If the following request also fails, the sensor shows an error.
• Set sensor to warning for 2 intervals, then set to down: Set the sensor to a Down status only after three consecutively failed requests.
• Set sensor to warning for 3 intervals, then set to down: Set the sensor to a Down status only after four consecutively failed requests.
• Set sensor to warning for 4 intervals, then set to down: Set the sensor to a Down status only after five consecutively failed requests.
• Set sensor to warning for 5 intervals, then set to down: Set the sensor to a Down status only after six consecutively failed requests.

Sensors that monitor via Windows Management Instrumentation (WMI) always wait at least one scanning interval before they show a Down status. It is not possible to immediately set a WMI sensor to a Down status, so the first option does not apply to these sensors. All other options can apply.

If you define error limits for a sensor's channels, the sensor immediately shows a Down status. No "wait" option applies.

If a channel uses lookup values, the sensor immediately shows a Down status. No "wait" options apply.

You cannot interrupt the inheritance for schedules, dependencies, and maintenance windows. The corresponding settings from the parent objects are always active. However, you can define additional settings here. They are active at the same time as the parent objects' settings.

Schedule

Select a schedule from the list. Schedules can be used to monitor for a certain time span (days or hours) every week.

You can create schedules, edit schedules, or pause monitoring for a specific time span. For more information, see section Account Settings—Schedules.

Schedules are generally inherited. New schedules are added to schedules that you already set up, so all schedules are active at the same time.

Maintenance Window

Specify if you want to set up a one-time maintenance window. During a maintenance window, the selected object and all child objects are not monitored. They are in a Paused status instead. Choose between:

• Not set (monitor continuously): No maintenance window is set and monitoring is always active.
• Set up a one-time maintenance window: Pause monitoring within a maintenance window. You can define a time span for a monitoring pause below and change it even for an active maintenance window.

To terminate an active maintenance window before the defined end date, change the time entry in Maintenance Ends to a date in the past.

Maintenance Begins

This field is only visible if you enable Set up a one-time maintenance window above. Use the date time picker to enter the start date and time of the maintenance window.

Maintenance Ends

This field is only visible if you enable Set up a one-time maintenance window above. Use the date time picker to enter the end date and time of the maintenance window.

Dependency Type

Define a dependency type. You can use dependencies to pause monitoring for an object depending on the status of a different object. You can choose from:

• Use parent: Use the dependency type of the parent object.
• Select a sensor: Use the dependency type of the parent object. Additionally, pause the current object if a specific sensor is in a Down status or in a Paused status caused by another dependency.

• Master sensor for parent: Make this sensor the master object for its parent device. The sensor influences the behavior of its parent device: If the sensor is in a Down status, the device is paused. For example, it is a good idea to make a Ping sensor the master object for its parent device to pause monitoring for all other sensors on the device in case the device cannot even be pinged. Additionally, the sensor is paused if the parent group is paused by another dependency.

To test your dependencies, select Simulate Error Status from the context menu of an object that other objects depend on. A few seconds later, all dependent objects are paused. You can check all dependencies under Devices | Dependencies in the main menu bar.

Dependency

This field is only visible if you enable Select a sensor above. Click the Search button and use the object selector to select a sensor on which the current object will depend.

Dependency Delay (Sec.)

This field is only visible if you enable Select a sensor above. Define a time span in seconds for dependency delay.

After the master sensor for this dependency comes back to an Up status, monitoring of the dependent objects is additionally delayed by the defined time span. This can prevent false alarms, for example, after a server restart, by giving systems more time for all services to start up. Enter an integer value.

This setting is not available if you set this sensor to Use parent or to be the Master sensor for parent. In this case, define delays in the parent device settings or in its parent group settings.

Click to interrupt the inheritance. See section Inheritance of Settings for more information.

User Group Access

Define the user groups that have access to the sensor. You see a table with user groups and group access rights. The table contains all user groups in your setup. For each user group, you can choose from the following group access rights:

• Inherited: Inherit the access rights settings of the parent object.
• No access: Users in this user group cannot see or edit the sensor. The sensor neither shows up in lists nor in the device tree.
• Read access: Users in this group can see the sensor and view its monitoring results. They cannot edit any settings.
• Write access: Users in this group can see the sensor, view its monitoring results, and edit its settings. They cannot edit its access rights settings.
• Full access: Users in this group can see the sensor, view its monitoring results, edit its settings, and edit its access rights settings.

For more details on access rights, see section Access Rights Management.